Zortrax M200 printer Forum Index

Zortrax M200 printer
Here is the forum to exchange, share feedbacks, and tips for our great Zortrax products.

 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Bad print
Goto page: 1, 2, 3  >
 
Post new topic   Reply to topic    Zortrax M200 printer Forum Index -> HARDWARE { M200 } -> PRINTING SAMPLES / Photos - videos
Previous topic :: Next topic  
Author Message
RobertKamieniarz


Offline

Joined: 26 Apr 2014
Posts: 16
Localisation: Leszno

PostPosted: Wed 7 May - 22:00 (2014)    Post subject: Bad print Reply with quote

PublicitéSupprimer les publicités ?
First print burned.


Back to top
Visit poster’s website
RobertKamieniarz


Offline

Joined: 26 Apr 2014
Posts: 16
Localisation: Leszno

PostPosted: Wed 7 May - 22:09 (2014)    Post subject: Bad print Reply with quote



Back to top
Visit poster’s website
RobertKamieniarz


Offline

Joined: 26 Apr 2014
Posts: 16
Localisation: Leszno

PostPosted: Wed 7 May - 22:13 (2014)    Post subject: Bad print Reply with quote

What am I doing wrong

Back to top
Visit poster’s website
jayceekeys


Offline

Joined: 31 Mar 2014
Posts: 26

PostPosted: Wed 7 May - 22:48 (2014)    Post subject: Bad print Reply with quote

Hi Robert!


It looks like you're suffering from warp - it's not uncommon on a large flat item. Have you cleaned the print bed with acetone and then used a glue stick to lightly apply a layer of glue to the bed before you print? Not sure where you are but most glue sticks work - UHU, Pritt Stick, Elmers etc


Cheers,


Jay Smile


Back to top
RobertKamieniarz


Offline

Joined: 26 Apr 2014
Posts: 16
Localisation: Leszno

PostPosted: Wed 7 May - 23:00 (2014)    Post subject: Bad print Reply with quote

Hi Jay
glue stick?
ok
thanks for the solution!


Back to top
Visit poster’s website
bluevoid


Offline

Joined: 23 Apr 2014
Posts: 13
Localisation: The Netherlands

PostPosted: Wed 7 May - 23:21 (2014)    Post subject: Bad print Reply with quote

Glue stick is the only thing that worked for me, after that I had no warp problems anymore. 
Do not apply to much though, sometimes I have trouble getting the abs off the platform Smile.


Back to top
Pioo


Offline

Joined: 13 Apr 2014
Posts: 14
Localisation: Poland

PostPosted: Wed 7 May - 23:48 (2014)    Post subject: Bad print Reply with quote

Zortrax First Aid Kit Smile




Back to top
Kyle


Offline

Joined: 29 Dec 2013
Posts: 69
Localisation: Colorado

PostPosted: Thu 8 May - 00:20 (2014)    Post subject: Bad print Reply with quote

I use Acetone with a little Z-ABS in it.. Scuffed up the bed a (SMALL) bit to take off the shine. No more warp.

Back to top
Catalin C.


Offline

Joined: 04 May 2014
Posts: 3
Localisation: Romania

PostPosted: Thu 8 May - 09:52 (2014)    Post subject: Bad print Reply with quote

Same glue as Pioo, without scuffing or acetone. Not too much, scrape it off after each print and apply new one.


Back to top
venosa


Offline

Joined: 30 Mar 2014
Posts: 12
Localisation: brasil

PostPosted: Thu 8 May - 13:31 (2014)    Post subject: Bad print Reply with quote

Acetone with ABS, simple, clean, works.

Back to top
RobertKamieniarz


Offline

Joined: 26 Apr 2014
Posts: 16
Localisation: Leszno

PostPosted: Thu 8 May - 22:17 (2014)    Post subject: Bad print Reply with quote

good advice for all
Acetone + glue Very Happy


Back to top
Visit poster’s website
Pioo


Offline

Joined: 13 Apr 2014
Posts: 14
Localisation: Poland

PostPosted: Thu 8 May - 22:28 (2014)    Post subject: Bad print Reply with quote

@Venosa … What proportions with aceton and ABS you use to make ABS juice??

Back to top
Ted


Offline

Joined: 21 Apr 2014
Posts: 6
Localisation: France

PostPosted: Fri 9 May - 10:21 (2014)    Post subject: Bad print Reply with quote

You also need to level you bed perfectly, it's very important.

Back to top
RobertKamieniarz


Offline

Joined: 26 Apr 2014
Posts: 16
Localisation: Leszno

PostPosted: Sat 10 May - 20:59 (2014)    Post subject: Bad print Reply with quote

new print, clean aceton + glue +





calibration Z
still bad printed



Back to top
Visit poster’s website
RobertKamieniarz


Offline

Joined: 26 Apr 2014
Posts: 16
Localisation: Leszno

PostPosted: Sat 10 May - 21:01 (2014)    Post subject: Bad print Reply with quote

Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad Evil or Very Mad
What am I doing wrong


Back to top
Visit poster’s website
Contenu Sponsorisé






PostPosted: Today at 02:27 (2018)    Post subject: Bad print

Back to top
Display posts from previous:   
Post new topic   Reply to topic    Zortrax M200 printer Forum Index -> HARDWARE { M200 } -> PRINTING SAMPLES / Photos - videos All times are GMT + 2 Hours
Goto page: 1, 2, 3  >
Page 1 of 3

 
Jump to:  

Portal | Index | Create own nforum | Free support forum | Free forums directory | Report a violation | Conditions générales d'utilisation
Powered by phpBB © 2001, 2005 phpBB Group